Browsing by Author "Kim, Hyeon-Cheol"

Now showing 1 - 2 of 2

Citation Count: 4
Effect of Shaft Length on the Torsional Resistance of Rotary Nickel-titanium Instruments
(Elsevier Science inc, 2020) Isik, Vasfiye; Kwak, Sang Won; Abu-Tahun, Ibrahim H.; Ha, Jung-Hong; Kayahan, Mehmet Baybora; Kim, Hyeon-Cheol
Introduction: This study was conducted to evaluate the effect of file length on the torsional resistance of nickel-titanium rotary files. Methods: Forty-five new files with a #25 tip size and variable taper for ProTaper Next (PTN; Dentsply Sirona, York PA), ProTaper Gold (PTG, Dentsply Sirona), and HyFlex CM (HCM; Coltene-Whaledent, Allstetten, Switzerland) were divided into 3 subgroups (n = 15) according to the file length (21, 25, and 31 mm). Torsional tests were performed using a custom-made device (AEndoS; DMJ System, Busan, Korea). The maximum torsional load and distortion angle were measured until file fracture occurred. The toughness was calculated using these data. All data were statistically analyzed using 2-way analysis of variance at a confidence level of 95%. One-way analysis of variance and Duncan post hoc comparison were also conducted to assess the difference among the independent variables, shaft length, and file system. Results: A statistically significant interaction was observed between the file system and instrument length with respect to the maximum torsional load (P < .05). The 31-mm shaft length of HCM showed higher maximum torsional load than that of the 25- and 21-mm shaft length in the HCM groups (P < .05). Among the instrument systems, PTG showed the significantly highest maximum torsional load followed by PTN and HCM (P < .05). The 31-mm shaft length of PTG showed significantly higher toughness than that of the 21- and 25-mm shaft lengths (P < .05), whereas PTN and HCM did not show any difference in relation to the shaft length. Conclusions: Within the limitations of this study, the instrument with a longer shaft may have higher maximum torsional load or toughness than that with a shorter shaft.
Citation Count: 8
Effective Establishment of Glide-Path to Reduce Torsional Stress during Nickel-Titanium Rotary Instrumentation
(Mdpi, 2019) Abu-Tahun, Ibrahim H.; Kwak, Sang Won; Ha, Jung-Hong; Sigurdsson, Asgeir; Kayahan, Mehmet Baybora; Kim, Hyeon-Cheol
This study compared the torque generation during canal shaping with a nickel-titanium endodontic instrument according to the extent of glide-path establishment. Seventy-five simulated S-shaped canal blocks were divided into five groups (n = 15) according to the number of repetitive insertions to the working length using a One G glide-path instrument: groups with 5, 10, 15, and 20 insertions as well as group Z without glide-path establishment. When the tip of the One G file reached the working length, the file was moved back and forth repetitively at the working length for the designated number of times for each group. The instrumentation procedure with HyFlex EDM had 15 pecking strokes. During instrumentation, the generated torque was transmitted to a customized data acquisition module and collected using customized software. Data were computed to determine the maximum torque and total stress. The maximum screw-in forces were statistically analyzed using one-way analysis of variance and Tukey's post hoc comparison test with a significance level of 95%. While the maximum stress did not have significant differences among the five groups (p > 0.05), groups with more than 10 repetitive insertions generated lower total stress during instrumentation than did the group with 5 insertions and group Z (p < 0.05). Under the limitations of this study, repetitive insertions of glide-path establishment files at the working length reduced stress generation during the shaping using nickel-titanium instruments.